The dangers associated with incorrectly hooking up jumper cables or battery chargers can cause a lot of damage, or even result in an exploding battery. The good news is that taking the time to understand why a car battery explodes can help prevent such a thing from happening.
Safely Connecting Jumper Cables or Battery Chargers
There are a few rules of thumb that can help you safely connect jumper cables, but there are also a number of special cases that supersede those rules. Before you use your car to provide a jumpstart, accept a jump from someone else, or hook up a charger to your battery, the first thing you need to do is check your owner’s manual to make sure your car doesn’t have designation connection points other than the battery. If your car has a battery in an unusual location, like a wheel well or the trunk, then there’s a chance that you’re supposed to use a junction block or another kind of remote connection. Regardless of the vehicles, the basic idea behind safely connecting jumper cables is to connect the electrical system of a donor vehicle, which has a good battery, to the electrical system of a vehicle with a dead battery. Positive should be connected to positive, and negative should be connected to negative. Connecting in the reverse order can damage both vehicles and create potentially hazardous sparks.
The Best Procedure for Safely Hooking up Jumper Cables
Follow these steps to hook up jumper cables to a car battery. Connecting a battery charger is done in much the same way, except instead of a donor battery, you’ll use a charger. The positive charger cable should be connected to the battery positive (+), after which the negative charger cable should be connected to bare metal on the engine or frame of the vehicle. There are some exceptions where positive is ground, but in most automotive electrical systems, negative is ground. That’s why you can connect a charger or a jumper cable to bare metal on the frame or engine of a vehicle with a dead battery and have current flow into the battery. It’s possible to connect directly to the battery’s negative terminal, and it may be easier in some cases. So if it’s possible, and it’s essentially the same thing as connecting to some other ground, why go through the trouble? Because you don’t want your battery to explode.
The Science of Exploding Car Batteries
Car batteries are referred to as lead acid because they use plates of lead submerged in sulfuric acid to store and release electrical energy. This technology has been around since the 18th century, and it isn’t efficient from either an energy-to-weight or energy-to-volume standpoint. However, they do have an excellent power-to-weight ratio, which means that they are good at providing the high levels of on-demand current required by automotive starters. The downside of lead-acid batteries, other than low efficiency, is that they’re made up of hazardous materials, and those hazardous materials can interact in dangerous ways. The presence of lead is the primary reason why car batteries have to be carefully and properly disposed of. The presence of sulfuric acid is why you have to take care when handling them unless you want holes in your clothes or chemical burns on your skin. The danger we’re most concerned with here is a sudden and catastrophic explosion, and the source of that hazard flows from the interaction between the lead and sulfuric acid in a battery. Small amounts of hydrogen gas are produced during both the process of discharge and during charging, and hydrogen is flammable. When a battery has discharged to the point where it can no longer power a starter motor, there’s a chance that some amount of hydrogen gas is still lingering inside the battery, or leaking out of the battery, just waiting for an ignition source. The same is true of a battery that has just been charged, as high voltages can lead to the formation of both oxygen and hydrogen.
Preventing Car Battery Explosions
There are two primary ignition sources that you have to worry about, and they can both be avoided with careful charging, jumping, and maintenance practices. The first ignition source is a spark created when connecting or disconnecting a jumper or charging cable. This is why it’s important to connect to bare metal on the engine or frame instead of the battery. If you hook up the negative jumper cable to the battery, any lingering hydrogen may be ignited by the ensuing spark. This is also why it’s a good idea to wait to turn on or plug in the charger until after it’s connected. The other type of car battery explosion still involves hydrogen gas, but the ignition source is inside the battery. If a battery isn’t properly maintained, and the electrolyte level is allowed to drop, the lead plates will be exposed to oxygen and may warp. This can lead to the plates flexing and touching during the extreme current drain initiated whenever you crank the starter motor, which can result in a spark inside the battery. That, in turn, can ignite any hydrogen present in the cell, causing the battery to explode.
What About Sealed Car Batteries?
There are two main types of sealed car batteries: traditional lead-acid batteries that aren’t serviceable and VRLA (valve-regulated lead-acid) batteries that don’t need to be serviced. In the case of VRLA batteries, the electrolyte is contained in a saturated glass mat or gel, so evaporation isn’t an issue. There is no need to add more electrolytes, and there is little danger of the plates being exposed to the air. Sealed batteries that use a liquid electrolyte, however, can cause issues later in life. If you have a VRLA battery, be it an absorbed glass mat or gel cell, the chances of the battery exploding are low. Still, it’s a good idea to follow the jumpstart and charging best practices so that you don’t get out of the habit. Maintenance of these batteries is almost impossible, so you don’t have to worry about checking the charge or electrolyte level regularly. Special care should be taken with non-VRLA sealed and maintenance-free batteries, since at least some level of evaporation will take place over time, and the situation will only get worse if the battery is allowed to fully discharge repeatedly, or if it’s overcharged with a high voltage. So while it’s a good idea to be careful around any battery when jump starting or charging it, it’s an even better idea to be careful when dealing with old, discharged, or recently charged non-VRLA sealed batteries.
